Lemote Fulong

I received a Lemote Fulong on August 21st, 2007. Here is everything that I have learned about it so far:

sources.list

I recently changed the sources.list to point to the following:

deb http://mirrors.kernel.org/debian/ unstable main non-free contrib

I have now set off a apt-get update; apt-get upgrade, and will see what happens. This may break things, but in the meantime things appear to be alright.

Out of the Box

By default out of the box, the Lemote Fulong comes installed with a modified version of debian. This is not really a bad thing, but it does have some odd things about it that are not part of a default install of debian (at least, not in my experience!)

• It is setup to boot straight into X. While this is not strange in and of itself, what is strange is that it boots straight into a user account with no password, using autologin via gdm.
• The root account is configured with a password. There is paperwork in the box with the machine detailing what the account passwords are and all, but if you are like me and cannot read Chinese, it might be a bit hard to decipher. As such, the password for the root account by default is "loongson".
• By default the network interface is configured for a static IP. I unfortunately deleted that portion before I got to writing this up, so I don't know what the exact IP is, but I do know it was one of the typical 192.168.0.x IP's.

lspci output

00:05.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:05.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:05.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:05.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:05.4 Non-VGA unclassified device: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:05.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50)
00:05.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 30)
00:06.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QZ [Radeon 7000/VE]
00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:08.0 USB Controller: NEC Corporation USB (rev 43)
00:08.1 USB Controller: NEC Corporation USB (rev 43)
00:08.2 USB Controller: NEC Corporation USB 2.0 (rev 04)

/proc/cpuinfo output

system type             : lemote-fulong
processor               : 0
cpu model               : ICT Loongson-2 V0.2  FPU V0.1
BogoMIPS                : 444.41
wait instruction        : no
microsecond timers      : yes
tlb_entries             : 64
extra interrupt vector  : no
hardware watchpoint     : no
ASEs implemented        :
VCED exceptions         : not available
VCEI exceptions         : not available

dmesg output

Linux version 2.6.21.3lm32 (loongson@debian) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #17 Thu Jun 14 14:18:13 CST 2007
busclock=66000000, cpuclock=668160000,memsize=256,highmemsize=768
CPU revision is: 00006302
FPU revision is: 00000501
Determined physical RAM map:
 memory: 0000000010000000 @ 0000000000000000 (usable)
 memory: 0000000010000000 @ 0000000010000000 (reserved)
 memory: 0000000030000000 @ 0000000020000000 (usable)
On node 0 totalpages: 81920
  DMA zone: 3 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 1021 pages, LIFO batch:0
  Normal zone: 276 pages used for memmap
  Normal zone: 80620 pages, LIFO batch:7
Built 1 zonelists.  Total pages: 81641
Kernel command line: console=tty root=/dev/hda1 
Primary instruction cache 64kB, physically tagged, direct mapped, linesize 32 bytes.
Primary data cache 64kB, 4-way, linesize 32 bytes.
Unified secondary cache 512kB 4-way, linesize 32 bytes.
Synthesized TLB refill handler (37 instructions).
Synthesized TLB load handler fastpath (49 instructions).
Synthesized TLB store handler fastpath (49 instructions).
Synthesized TLB modify handler fastpath (48 instructions).
arch init irq
PID hash table entries: 4096 (order: 12, 32768 bytes)
Using 334.080 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 7, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 6, 1048576 bytes)
Memory: 1035040k/1048576k available (2933k kernel code, 12960k reserved, 967k data, 144k init, 0k highmem)
Calibrating delay loop... 444.41 BogoMIPS (lpj=888832)
Mount-cache hash table entries: 1024
Checking for the multiply/shift bug... no.
Checking for the daddi bug... no.
Checking for the daddiu bug... no.
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
via686b fix: ISA bridge
via686b fix: ISA bridge done
via686b fix: IDE
via686b fix: IDE done
PCI quirk: region eee0-eeef claimed by vt82c686 SMB
ac97 interrupt = 9
ac97 rev=80
Setting sub-vendor ID & device ID
sub vendor-device id=47101005
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 16384 (order: 3, 131072 bytes)
TCP established hash table entries: 65536 (order: 6, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 5, 524288 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
fuse init (API version 7.8)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
radeonfb (0000:00:06.0): Invalid ROM signature ffff should be 0xaa55
xtal calculation failed: 26564
radeonfb: Used default PLL infos
radeonfb: Reference=27.00 MHz (RefDiv=67) Memory=166.00 Mhz, System=166.00 MHz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type CRT found
radeonfb: Monitor 2 type no found
Console: switching to colour frame buffer device 80x30
radeonfb (0000:00:06.0): ATI Radeon QZ 
rtc: SRM (post-2000) epoch (2000) detected
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
loop: loaded (max 8 devices)
8139too Fast Ethernet driver 0.9.28
eth0: RealTek RTL8139 at 0x9000000016032000, 00:xx:xx:xx:xx:xx, IRQ 58
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:05.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:05.1
    ide0: BM-DMA at 0x5040-0x5047, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x5048-0x504f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: HTS421240H9AT00, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 78140160 sectors (40007 MB) w/1570KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
ehci_hcd 0000:00:08.2: EHCI Host Controller
ehci_hcd 0000:00:08.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:08.2: irq 60, io mem 0x16032100
ehci_hcd 0000:00:08.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:08.0: OHCI Host Controller
ohci_hcd 0000:00:08.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:08.0: irq 58, io mem 0x16030000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0000:00:08.1: OHCI Host Controller
ohci_hcd 0000:00:08.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:08.1: irq 59, io mem 0x16031000
usb 1-3: new high speed USB device using ehci_hcd and address 2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-3: configuration #1 chosen from 1 choice
usb 3-2: new full speed USB device using ohci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
hub 3-2:1.0: USB hub found
hub 3-2:1.0: 3 ports detected
usb 3-2.1: new low speed USB device using ohci_hcd and address 3
usb 3-2.1: configuration #1 chosen from 1 choice
usb 3-2.3: new full speed USB device using ohci_hcd and address 4
usb 3-2.3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
atkbd.c: keyboard reset failed on isa0060/serio1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 144k freed
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:05.2: UHCI Host Controller
uhci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:05.2: irq 10, io base 0x00005000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new interface driver hiddev
uhci_hcd 0000:00:05.3: UHCI Host Controller
uhci_hcd 0000:00:05.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:05.3: irq 11, io base 0x00005020
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input1
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:08.1-2.1
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2
input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:08.1-2.3
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input3
input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:08.1-2.3
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PCI: Setting latency timer of device 0000:00:05.5 to 64
Adding 1023968k swap on /dev/hda3.  Priority:-1 extents:1 across:1023968k
EXT3 FS on hda1, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1